Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
Just how do you really feel when it comes to Installing A Bathtub?
Mounting a bathtub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old tub with a brand-new one is also a moderately tough job. If the old tub is conveniently obtainable, the job can relocate immediately; if you need to open a wall to get rid of the old bathtub and also position the brand-new bathtub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly need an assistant to move out the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the job and also fit trying it. Instead of working with a contractor to take control of a halfway-completed job, it is better to consider using one prior to you begin. Opportunities are you may need a specialist plumber to make tube links.
This article will assist you set up a brand-new tub in your bathroom if you have already gotten a new tub as well as do not require to transform the plan of your previous supply of water pipelines.
Your tools and material checklist should comprise the following:
Getting ready for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to stop stress on the tub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be suited its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be fairly troublesome due to the limited gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, put the tub in the required setting. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bath tub until the level reads degree.
To mount faucets, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints as well as new pipework for leakages and tighten them if necessary. Load the tub as well as also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, deal with the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub must wait until the bath tub has actually been used at least once as this will certainly settle it into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washing machines remain in area between the tap and the sink. Secure the tap in position with the producer offered backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet ports. The former type ought to be connected to the faucet ends initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split a rigid seal, causing the water to penetrate the wall surface between the bath and the tiling, causing complications with moisture and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealer can crack fairly very early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that report on How to Install a Bathtub Yourself from a friend on another web property. In case you appreciated our article plz do not forget to share it. We appreciate reading our article about How to Install a Bathtub Yourself.
Schedule Now! Report this page